Data Sheet: NM-2450-2G

2.4 GHz ISM Band – 2×2 MIMO Broadband Transceiver with Power Booster

Designed in the compact miniPCI-Express form factor, the NM-2450-2G is Rugged, Long Range, 2×2 MIMO streams, IEEE 802.11n compliant Radio subsystem.  It is developed specifically for applications requiring high throughput over very long range in the rugged environments. The NM-2450-2G consists of a high throughput 802.11n radio and 2x bi-directional, tiny Power Amps carefully tuned and calibrated together to deliver high performance. The NM-2450-2G radio operates on 2412 MHz~2484 MHz bands.

Target Applications 

The NM-2450-2G is ideal for applications that require wireless links with very high throughput. With high gain antennas, the user can expect to get range of over 25 Km.

  • Mesh applications
  • Drones and Robots
  • Point-to-Point links
Model No. NM-2450-2G (Rugged, 802.11n, ath9k driver)
 Special Features – Extended lifespan with planned availability for long time
– Extreme Reliability, IPC Class 2 standard with Class 3 options
– Compliant to MIL-STD-202G, Qualified for high shock/vibration environments
MAC Chipset QCA9590-BR4B with Extended Temperature range
Software Support Open Source Linux Driver ath9k for 11n models OpenWRT (Wireless Router/Linux OS)
Center Frequency Range 2.412 GHz ~ 2.484 GHz. This varies by the regulatory domain
Channel Bandwidth* 20, and 40 MHz channels
Radio Modulation (Auto Adjust) BPSK, QPSK, 16 QAM, and 64 QAM (5.x GHz – 11n models)
Data Rates Supported 802.11n: MCS0-15
802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps (2.4 GHz)
802.11n version 2.0 Capabilities  ● 802.11 dynamic frequency selection (DFS) as an AP and Client ● Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx), Maximal ratio combining (MRC), Cyclic shift diversity (CSD), Frame aggregation, block ACK, 802.11e compatible bursting, Spatial multiplexing, cyclic-delay diversity (CDD), low-density parity check (LDPC), Space Time Block Code (STBC)
Operating Modes AP, Client and Adhoc modes to implement Access Point, PtP, PtmP, and Mesh networks
MAC Protocol TDD with Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA)
Wireless Error Correction FEC, ARQ
Wireless Data Security 128 bit AES, WEP, TKIP and WAPI hardware encryption. Support for IEEE 802.11d, e, h, i, k, r, v, w and time stamp standards
FIPS Certification

Small packet size (96 bytes) in AES encryption at full packet rate.

FIPS 140-2, Level 2 (Temper Evidence Shield), Loop back mode to facilitate FIPS AES certification.
Tx/Rx Specification  Radio Modulation Coding
Max Tx Power
(± 2 dB)**
Rx Sensitivity
2.4 GHz (20 MHz Channel) – 11n models
802.11b, STBC BPSK 1/2
30 -98
64 QAM 3/4
24 -81
802.11n BPSK 1/2 30 -94
16 QAM 3/4 30 -83
64 QAM 5/6 24 -72
2.4 GHz (40 MHz Channel) – 11n models
802.11n BPSK 1/2 30 -91
802.11n  16 QAM 3/4 30 -79
802.11n  64 QAM 5/6 24 -70
* It is advantageous to use the smallest Channel Bandwidth that can support the Throughput requirements. Smaller bandwidths provide more channels to choose and help avoid interference issues. The system’s SNR is higher at smaller Channel Bandwidths and Range is longer.
** Total power for all streams
Antenna Signal Strength
-35 dBm to -85 dBm (Recommended), (Absolute Maximum=+12 dBm)
Interference Immunity SAW filters on RF ports for immunity against high power cellular transmissions in the neighboring bands.
Antenna port isolation for concurrent operation Up to +10 dBm signal strength for 5 GHz signal without degrading 2.4 GHz operation
Integrated Antenna Port Protection >20 KV (Human Body Model)
Receiver LNA Gain +10 dB
Receiver Adjacent Channel Rejection (ACR) >18 dB @ 11a, 6 Mbps (Typ)
Receiver Alternate Channel Rejection (ALCR) >35 dB @ 11a, 6 Mbps (Typ)
Receive chain Noise Figure +6 dB
Transmitter Adjacent Channel Leakage power Ratio (ACLR) 
45 dB (Fc ± ChBW)
Transmitter Spurious Emission Suppression -40 dBc
RF Hardware Disable (RF Kill) Pin 20 of miniPCI-E interface. (Required for FAA compliance) 
Control for External Power Amp DC biased signal over RF ports
RF Power control In 0.5 dBm steps. Accuracy of power calibration loop ±2 dBm. Each transceiver individually calibrated and tested.
Antenna Ports 2 MMCX Ports (50 Ohms)
Host CPU Board Any CPU board with Industry standard miniPCI-Express interface with minimum 6 mm connector height    
Operating Voltage 3.3 Volts from miniPCI-E interface for radio
6-42V for Front-End-Subsystem
-Power Consumption Total 14W (12W @ Max power for FES, in data transfer mode on all chains + 2W for radio module)
Total 10W (8W @ 20 dBm power for FES in continuous data transfer mode on all chains + 2W for radio module)
1.2W total power in continuous data receive mode
Shield case temperature range (Operating) -40°C to +85°C
The System’s thermal design should ensure that the transceiver’s shield case temperature is maintained within these specifications. Prism-FES can be mounted away from the host CPU board for better thermal design
Cable Assembly Samples Include the harness with RF cable and DC power
Humidity (Operating) 0% – 95% (Non-condensing)    
Dimensions 1x 30 x 50 x 6 mm Radio module, 60 x 52 x 7 mm FES modules, Weight=60 grams (14+46)
Mechanical drawing and 3D-CAD files available upon request    
Regulatory Requirements Designed and Verified to meet various regulatory requirements. Formal testing and approval is required based on the Integrator’s particular host platform. The Integrator is also responsible for obtaining any other required regulatory approvals in target markets for the finished product. Doodle Labs can offer assistance for compliance testing of the System Integrator’s host platform.
CE Certification Certificate # TCT160601E007C. in conformity with all the requirements of the European Directive 1999/5/EC – EN 301 893 V1.8.1, EN 300 328 V.1.8.1, EN 301 489-1 V1.9.2, EN 301 489-17 V2.2.1, EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011+ A2:2013
IC Certification 21411-NM24502F
RoHS/WEEE Compliance  Yes. 100% Recyclable/Biodegradable packaging    

* Specifications are subject to change without prior notice.